Primers

Alseal 143P High Temp Phenolic

Water-based one-component phenolic coating. Excellent adhesion and flow combined with a low perm film provide high insulative strength. Also exhibits high chemical resistance and operating temperatures to 400°F (204°C) continuous, peaking to 600°F (316°C). Cures at 400°F (204°C).

Alseal 189P High Temp Phenolic

Alseal 189P is a high temperature water-based two component phenolic / epoxy coating composition containing laminar orienting pigments.

Alseal 220i Cr-Free Inorganic Aluminum/Ceramic

Alseal 220i is a single component, chrome-free coating composition formulated to protect ferrous alloys from both high temperature heat oxidation and at the same time offer sacrificial (cathodic) protection to the base metal.

Alseal 500 Low Temp Cure Aluminum/Ceramic

A high-temperature coating composition with aluminum powder in an inorganic binder. Provides sacrificial corrosion protection to temperatures up to 1100°F (593°C) and heat oxidation protection to temperatures as high as 1600°F (871°C). Can be cured as low as 350°F (177°C). Not suitable for use on mild steel substrates.

Alseal 5050 Cr-Free Inorganic Aluminum/Ceramic

Alseal 5050 is a single component, chrome-free coating composition formulated to protect ferrous alloys from both high temperature heat oxidation and at the same time offer sacrificial (cathodic) protection to the base metal.

Alseal 518 Inorganic Aluminum/Ceramic

A high-temperature coating composition containing aluminum powder in an inorganic binder. Provides sacrificial corrosion protection to temperatures up to 1100°F (593°C) and heat oxidation protection up to 1600°F (871°C). Must be cured at a minimum temperature of 400°F (204°C). Suitable for use on all steel substrates.

Alseal 519 Inorganic Aluminum/Ceramic

Formulated to provide smoother surface finishes and higher erosion resistance than Alseal 518 while still providing all the corrosion protection and high-temperature properties.

Alseal 585 Dip Applied Aluminum/Ceramic

A high-temperature dip-applied coating composition with aluminum powder in an inorganic binder. Provides sacrificial corrosion protection to temperatures up to 1100°F (593°C) and heat oxidation protection to temperatures as high as 1600°F (871°C). Can be cured as low as 350°F (177°C). Not suitable for use on mild steel substrates.  Alseal 585 exhibits an increased viscosity …

Alseal 585 Dip Applied Aluminum/Ceramic Read More »

Alseal 5K Cr-Free Inorganic Aluminum/Ceramic

A completely chromium-free aluminum ceramic coating with no known carcinogens, HAPs or VOCs, Alseal 5K provides sacrificial corrosion protection and heat oxidation protection to temperatures of 1100°F (593°C).

Alseal 625 Diffusion Aluminide

Alseal 625 is a slurry applied diffusion aluminide coating made of aluminum and silicon powder in an inorganic binder. The aluminide formed from diffusion into Cobalt or Nickel based alloys provides a very wear resistant and heat oxidation resistant surface.

Alseal DB-3 Silicone/Ceramic

Two-component water-based silicone-ceramic topcoat for use over Alseal basecoats. Chemically passivates and physically seals sacrificial corrosion resistant aluminum-ceramic basecoats, at temperatures up to 700oF (371oC).  Available in multiple colors.

Alseal HX Bright Aluminum/Ceramic

An aluminum-ceramic coating formulated to readily polish to a reflective finish that remains bright and shiny up to 1100°F (593°C) without discoloring. Used on hot automotive components as an alternative to bright chrome plating.

Redilube 140 Phenolic w/MoS2

Redilube 140 is a high temperature solid film lubricant containing molybdenum disulfide in a water-based phenolic binder.

Siloxseal 350 High Temp Silicone

High temperature silicone coating. Protects steel in service temperatures up to 1200°F (649°C) Newest water-based silicone technology provides excellent properties with a low VOC Air dry characteristics offer ease of handling until placed in service

Siloxseal 385 Mid Temp Silicone

Silicone modified epoxy coating with enhanced thermal resistance capabilities. Excellent for protecting outdoor structural steel, pipes, and equipment from corrosion. Withstands operating temperatures of up to 400°F (204°C). Adheres well to difficult surfaces such as brass or copper.

U-104 Aluminum-Filled MCU

A single-component, aluminum-filled, moisture-cured urethane, U-104 excels at protecting steel and other substrates from corrosion, even over pre-rusted surfaces. Because it bonds and encapsulates the substrate, it may not require aggregate blasting for surface preparation. It cures fast, easily allowing two coats in one day. With two or three coats, it can be used as …

U-104 Aluminum-Filled MCU Read More »

U-109 Zinc Rich MCU

U-109 is a two-component, zinc-rich urethane primer for use on metal substrates in severe corrosive or salt environments or anywhere the substrate requires cathodic-type protection from its primer. Designed for easy application by brush, roller or spray, it provides long-term corrosion protection. When paired with U-166, U-499 or U-111 as a topcoat, it provides added …

U-109 Zinc Rich MCU Read More »

U-497 Zinc Rich Epoxy Primer

U-497 is a three-component, zinc-rich polyamide epoxy primer for use on metal substrates in severe corrosive or salt environments or anywhere the substrate requires cathodic-type protection from its primer. Designed for easy application by brush, roller or spray, it provides long-term corrosion protection. When paired with U-166, U-499 or U-111 as a topcoat, it provides …

U-497 Zinc Rich Epoxy Primer Read More »

U-499 Polyamide Epoxy Primer

Designed to be applied in many environments, even on damp surfaces, U-499 is a two-component polyamide epoxy with corrosion inhibiting pigments that helps prevent corrosion and attack from sea-water and chemicals. It will cure when cold, and when cured at normal temperatures, can be ready for immersion in as little as 8 hours.

WearCOAT 1020 WB Epoxy Primer

Two component, water-based penetrating epoxy sealer/primer for protecting concrete surfaces. Quick cure provides a short time to overcoat Low viscosity allows penetration into the pores of concrete for increased adhesion Can be used as a primer, or as a final coat sealer

WearCOAT 1080 Moisture Mitigating Primer

Two component, 100% solids, moisture vapor tolerant epoxy primer for use on mechanically prepared concrete floors. Excellent in lowering moisture vapor pressure prior to applying standard coatings Effective for lowering moisture vapor transmission under resilient flooring and tile

WearCOAT 3030 Natural Sealer

Water-based clear concrete surface sealer.  This low-odor, fast cure sealer helps keep water, salts and stains from penetrating concrete and does not change the appearance of the surface.  Applies easily with return-to-service in as little as 4 hours.  For indoor or outdoor use on concrete, rock or slate-based surfaces.

WearCOAT 3045 Darkening Sealer

Excellent water-based sealer yields a wet-look previously only achieved with solvent-based acrylic sealers.  Low-odor, UV-resistant formula cures in as little as 4 hours.  Helps keep water, salts and stains from penetrating while giving a dark, wet appearance.  For indoor or outdoor use on concrete, rock or natural slate-type surfaces.

WearCOAT 490 Polyamide Epoxy Primer

Two component polyamide cured epoxy primer. Very surface tolerant and can be applied in damp environments Long recoat window allows excellent topcoat adhesion Usually top coated with WearCOAT 440, WearCOAT 491, or WearCOAT 100