Environment: Indoor

Alseal 143P High Temp Phenolic

Water-based one-component phenolic coating. Excellent adhesion and flow combined with a low perm film provide high insulative strength. Also exhibits high chemical resistance and operating temperatures to 400°F (204°C) continuous, peaking to 600°F (316°C). Cures at 400°F (204°C).

Alseal 189P High Temp Phenolic

Alseal 189P is a high temperature water-based two component phenolic / epoxy coating composition containing laminar orienting pigments.

Alseal 190P Phenolic/Urethane w/PTFE

Water-based one-component urethane modified phenolic with particulate PTFE for improved slip and release at temperatures up to 350°F (177°C) continuous, peaking to 500°F (260°C). Has excellent adhesion to most metals and improved flexibility over conventional phenolics.

Alseal 320 Urethane w/PTFE

A water-based polyurethane dispersion containing PTFE. Offers a high level of slip-and-release coupled with a room-temperature cure. Maximum service temperatures of 250°F (121°C).

Alseal 360 Silicate w/Graphite

A high-temperature coating composition containing a graphite blend in an inorganic binder. Air-dry coating protects mating parts from seizing and galling at temperatures up to 1200°F (649°C).

Alseal 370 Silicate DFL

A high-temperature coating composition containing a graphite/molybdenum disulfide blend in an inorganic binder. Air-dry coating protects mating parts from seizing and galling at temperatures up to 800°F (427°C).

Alseal 500 Low Temp Cure Aluminum/Ceramic

A high-temperature coating composition with aluminum powder in an inorganic binder. Provides sacrificial corrosion protection to temperatures up to 1100°F (593°C) and heat oxidation protection to temperatures as high as 1600°F (871°C). Can be cured as low as 350°F (177°C). Not suitable for use on mild steel substrates.

Alseal 5050 Cr-Free Inorganic Aluminum/Ceramic

Alseal 5050 is a single component, chrome-free coating composition formulated to protect ferrous alloys from both high temperature heat oxidation and at the same time offer sacrificial (cathodic) protection to the base metal.

Alseal 518 Inorganic Aluminum/Ceramic

A high-temperature coating composition containing aluminum powder in an inorganic binder. Provides sacrificial corrosion protection to temperatures up to 1100°F (593°C) and heat oxidation protection up to 1600°F (871°C). Must be cured at a minimum temperature of 400°F (204°C). Suitable for use on all steel substrates.

Alseal 519 Inorganic Aluminum/Ceramic

Formulated to provide smoother surface finishes and higher erosion resistance than Alseal 518 while still providing all the corrosion protection and high-temperature properties.

Alseal 5200 Cr-Free Ceramic Topcoat

Alseal 5200 is a chromium-free ceramic topcoat for use over Alseal 5K basecoat. Topcoated systems are stable at temperatures up to 1100oF (593oC). Contact CFI for available colors.

Alseal 528 Inorganic Zirconia/Ceramic

A high-temperature coating composition containing zirconium oxide powder in an inorganic binder. Protects ferrous alloys against thermal oxidation and corrosion. Withstands service temperatures in excess of 2000°F (1093°C) and is very tolerant to thermal cycling.

Alseal 585 Dip Applied Aluminum/Ceramic

A high-temperature dip-applied coating composition with aluminum powder in an inorganic binder. Provides sacrificial corrosion protection to temperatures up to 1100°F (593°C) and heat oxidation protection to temperatures as high as 1600°F (871°C). Can be cured as low as 350°F (177°C). Not suitable for use on mild steel substrates.  Alseal 585 exhibits an increased viscosity …

Alseal 585 Dip Applied Aluminum/Ceramic Read More »

Alseal 590 Inorganic Ceramic/PTFE

A two-component, high-temperature coating composition containing PTFE. Promotes release of hot or sticky parts and dirt for environments up to 550oF (288oC). Inorganic binder allows release of very difficult organic materials. Reduces friction while functioning as an anti-stick/anti-fouling sealer over Alseal 500, 518, and 519.

Alseal 591M Inorganic Ceramic/MoS2

A one-component, self-priming ceramic coating that contains particulate molybdenum disulfide.  Stable up to 800oF (427oC).  Self-priming, so it can also be used alone as a lubricant or release agent.

Alseal 598 Inorganic Ceramic

A high-temperature resistant inorganic coating composition for use over Alseal 500, 518, and 519. Enhances the smoothness of the Alseal basecoats and extends the long-term corrosion protection by retarding the sacrificial consumption of these coatings. Available in multiple colors.

Alseal 598SC Smooth Ceramic Topcoat

A modified version of Alseal 598 formulated to improve surface finish, only available in a clear/semi-translucent version. Lowers the surface finish 10 microinches or more when compared to standard Alseal 598.

Alseal 5K Cr-Free Inorganic Aluminum/Ceramic

A completely chromium-free aluminum ceramic coating with no known carcinogens, HAPs or VOCs, Alseal 5K provides sacrificial corrosion protection and heat oxidation protection to temperatures of 1100°F (593°C).

Alseal 5KTC Cr-Free Ceramic Topcoat

A chromium-free ceramic topcoat for use over Alseal 5K basecoat.  Topcoated systems are stable at temperatures up to 1100oF (593oC).  Contact CFI for available colors.

Alseal 625 Diffusion Aluminide

Alseal 625 is a slurry applied diffusion aluminide coating made of aluminum and silicon powder in an inorganic binder. The aluminide formed from diffusion into Cobalt or Nickel based alloys provides a very wear resistant and heat oxidation resistant surface.

Alseal DB-3 Silicone/Ceramic

Two-component water-based silicone-ceramic topcoat for use over Alseal basecoats. Chemically passivates and physically seals sacrificial corrosion resistant aluminum-ceramic basecoats, at temperatures up to 700oF (371oC).  Available in multiple colors.

Alseal HX Bright Aluminum/Ceramic

An aluminum-ceramic coating formulated to readily polish to a reflective finish that remains bright and shiny up to 1100°F (593°C) without discoloring. Used on hot automotive components as an alternative to bright chrome plating.

FlexRez 150 Flexible PUD

FlexRez 150 is a water based aliphatic polyurethane dispersion (PUD) and is intended for use as a binder for clear or pigmented coatings that require extremely high flexibility and excellent adhesion.

FlexRez 155 Flexible Low-Gloss PUD

FlexRez 155 is a water based aliphatic polyurethane dispersion (PUD) and is intended for use as a binder for clear or pigmented coatings that require extremely high flexibility and excellent adhesion. Formulated to provide a low gloss finish.

Redilube 140 Phenolic w/MoS2

Redilube 140 is a high temperature solid film lubricant containing molybdenum disulfide in a water-based phenolic binder.

Redilube 150 Cr-Free Phenolic w/PTFE

Water-based one-component phenolic with particulate PTFE for improved slip and release at temperatures up to 400°F (204°C) continuous, peaking to 600°F (316°C). Has excellent adhesion to most metals combined with high chemical resistance.

Siloxseal 350 High Temp Silicone

High temperature silicone coating. Protects steel in service temperatures up to 1200°F (649°C) Newest water-based silicone technology provides excellent properties with a low VOC Air dry characteristics offer ease of handling until placed in service

Siloxseal 385 Mid Temp Silicone

Silicone modified epoxy coating with enhanced thermal resistance capabilities. Excellent for protecting outdoor structural steel, pipes, and equipment from corrosion. Withstands operating temperatures of up to 400°F (204°C). Adheres well to difficult surfaces such as brass or copper.

Sunlube 320 Urethane w/Wax Dispersion

Sunlube 320 is a single component non-toxic dry film lubricant consisting of a wax and a film forming polymer which holds the wax onto the surface, allowing for longer life than standard wax lubricants.

U-104 Aluminum-Filled MCU

A single-component, aluminum-filled, moisture-cured urethane, U-104 excels at protecting steel and other substrates from corrosion, even over pre-rusted surfaces. Because it bonds and encapsulates the substrate, it may not require aggregate blasting for surface preparation. It cures fast, easily allowing two coats in one day. With two or three coats, it can be used as …

U-104 Aluminum-Filled MCU Read More »

U-111 Polyester Urethane Topcoat

CFI’s flagship topcoat, U-111 is a two-component polyester urethane finish coating for exterior applications. With outstanding chemical and abrasion resistance far better than most other epoxy and urethane coatings, this proven formula can withstand years of exposure to solvents and caustics, and is easily cleaned. It is the ideal coating for anti-graffiti applications when solvents …

U-111 Polyester Urethane Topcoat Read More »

U-166 Acrylic Urethane

U-166 is an acrylic urethane finish coat designed for exterior application on a variety of substrates, including steel, aluminum and concrete. Non-yellowing and non-chalking, it offers good chemical and excellent weather resistance and gloss retention. It is offered in standard full gloss and semi-gloss colors and clear, and can be color-matched upon request.

U-3013 Conductive Urethane

U-3013 is a single component water based aromatic urethane coating providing electrostatic discharge.

U-3060 ESD Flexible Urethane ESD

Water-based one-component aliphatic urethane coating that exhibits extreme elongation and flexibility for protecting fabric and textiles. Provides good erosion resistance. Provides electrostatic dissipation by using next generation conductive pigments which will not lose efficacy over time like traditional carbon pigments.  Conductivity range is 106 to 108 ohms per square.

U-3060 WB Flexible Urethane

Water-based one-component aliphatic urethane coating that exhibits extreme elongation and flexibility for protecting fabric and textiles. Provides good erosion resistance.

U-313 Flexible Polyester Urethane

Two component, aliphatic urethane, flexible, polyester type, finish coating for exterior applications. Extreme flexibility and toughness Excellent erosion resistance UV stable for extended weathering Adheres to a variety of substrates Good chemical resistance

U-497 Zinc Rich Epoxy Primer

U-497 is a three-component, zinc-rich polyamide epoxy primer for use on metal substrates in severe corrosive or salt environments or anywhere the substrate requires cathodic-type protection from its primer. Designed for easy application by brush, roller or spray, it provides long-term corrosion protection. When paired with U-166, U-499 or U-111 as a topcoat, it provides …

U-497 Zinc Rich Epoxy Primer Read More »

U-498 Polyamide Epoxy Topcoat

A two-component high-build, high-solids novolac epoxy, this proven U-Series™ topcoat is highly surface tolerant. It can be applied in damp environments; once it has air-cured – typically in 8 hrs – it may be returned to service in wet or even submerged environments. This topcoat provides good abrasion and chemical resistance, making it ideal for …

U-498 Polyamide Epoxy Topcoat Read More »

U-499 Polyamide Epoxy Primer

Designed to be applied in many environments, even on damp surfaces, U-499 is a two-component polyamide epoxy with corrosion inhibiting pigments that helps prevent corrosion and attack from sea-water and chemicals. It will cure when cold, and when cured at normal temperatures, can be ready for immersion in as little as 8 hours.

U-571 100% Solids Novolac Epoxy

U-571 is best suited to applications subject to spills and splashes of acids and bases, epoxy novolacs offer enhanced resistance to chemicals. The 100 percent solids formulation offers zero V.O.C., low odor, and a high-build finish.

WearCOAT 100 Polyester Urethane Topcoat

Two component, polyester aliphatic urethane finish coating for high-performance flooring. Resists tire marking under the heaviest of loads, making it ideal for heavy wheeled-traffic applications Abrasion resistance is 3x better than standard epoxy flooring Non-yellowing, non-chalking properties combined with excellent abrasion, chemical, solvent and good heat resistance properties Provides excellent gloss retention and will continue …

WearCOAT 100 Polyester Urethane Topcoat Read More »

WearCOAT 1020 WB Epoxy Primer

Two component, water-based penetrating epoxy sealer/primer for protecting concrete surfaces. Quick cure provides a short time to overcoat Low viscosity allows penetration into the pores of concrete for increased adhesion Can be used as a primer, or as a final coat sealer

WearCOAT 1080 Moisture Mitigating Primer

Two component, 100% solids, moisture vapor tolerant epoxy primer for use on mechanically prepared concrete floors. Excellent in lowering moisture vapor pressure prior to applying standard coatings Effective for lowering moisture vapor transmission under resilient flooring and tile

WearCOAT 2020 Quick Cure Polyaspartic

Two component, fast-setting, zero VOC, high solids, UV stable polyaspartic coating. Fast cure for quick return to service UV stable Good abrasion resistance Very low odor High gloss finish

WearCOAT 2035 Slow Cure Polyaspartic

Two component, moderate cure speed, zero VOC, high solids, UV stable polyaspartic coating. Slower cure than conventional polyaspartic coatings reduces dry roller marks Highly UV stable Good abrasion resistance Very low odor High gloss finish

WearCOAT 2345 High-Wear Low VOC Urethane

Two component, high solids, low VOC, UV stable, high-wear urethane coating with a satin finish and light anti-slip texture. UV stable Excellent abrasion resistance Very low odor Good chemical resistance Light anti-slip texture

WearCOAT 3015 WB Polyester Urethane

Single component, water-based, low odor, aliphatic urethane top coat. Durable, color-stable surface for foot and light-wheel traffic applications Very low odor Fast-dry with satin finish

WearCOAT 3045 Darkening Sealer

Excellent water-based sealer yields a wet-look previously only achieved with solvent-based acrylic sealers.  Low-odor, UV-resistant formula cures in as little as 4 hours.  Helps keep water, salts and stains from penetrating while giving a dark, wet appearance.  For indoor or outdoor use on concrete, rock or natural slate-type surfaces.

WearCOAT 440 100% Solids Epoxy

Two component, 100% solids epoxy floor coating. Formulated for general industrial flooring as an excellent high-build mid-coat Can be pigmented or used clear Ideal for use as a broadcast binder for flake, sand, or quartz media Very high resistance to amine blush making it ideal for application in most environments Also available in a fast …

WearCOAT 440 100% Solids Epoxy Read More »

WearCOAT 440FS 100% Solids Epoxy

Two component, 100% solids fast curing epoxy floor coating. Formulated for general industrial flooring as an excellent high-build mid-coat Can be pigmented or used clear Ideal for use as a broadcast binder for flake, sand, or quartz media Very high resistance to amine blush making it ideal for application in most environments Fast Set allows …

WearCOAT 440FS 100% Solids Epoxy Read More »

WearCOAT 460 100% Solids Epoxy

Two component, 100% solids high-build floor coating. Formulated for general industrial flooring as an excellent extra-high-build mid-coat Unique blend of additives provides a self-leveling coating in a high-build formulation; it rolls out quickly and easily, virtually eliminating heavy roller drag Pigmented Very high resistance to amine blush making it ideal for application in most environments

WearCOAT 481HP UV Stabilized Epoxy

Two component, light-stabilized, reduced yellowing, 100% solids high performance specialty epoxy floor coating. Offers good resistance to UV exposure; WearCOAT 481HP will yellow in color, but at half the rate of traditional epoxy floor coatings Good build properties Excellent flow and surface wetting with increased flexibility and resilience, offering about 30% better wear than conventional …

WearCOAT 481HP UV Stabilized Epoxy Read More »

WearCOAT 490 Polyamide Epoxy Primer

Two component polyamide cured epoxy primer. Very surface tolerant and can be applied in damp environments Long recoat window allows excellent topcoat adhesion Usually top coated with WearCOAT 440, WearCOAT 491, or WearCOAT 100

WearCOAT 491 Polyamide Epoxy Topcoat

Two component high-build, high solids polyamide cured novolac epoxy finish coating. Very surface tolerant and can be applied in damp environments Economical coating with good abrasion and chemical resistance Use with WearCOAT 490 or WearCOAT 1020 primers

WearCOAT 570 100% Solids Novolac Epoxy

Two component, 100% solids, high-build novolac epoxy floor coating for surface protection against severe chemical attack. High chemical resistance, especially to acids Low VOC, low odor application Easily applied by brush or roller

WearCOAT SG-1 Epoxy Ester Anti-Slip

Single component, epoxy ester, anti-slip floor and deck coating for heavy pedestrian use. Designed for application in areas of heavy pedestrian traffic Offers excellent adhesion to a variety of surfaces

WearCOAT SG-3 Epoxy Anti-Slip

Two component, catalyzed, nonskid epoxy coating for use with heavy vehicular traffic. Provides safer footing and better traction for personnel and equipment Excellent chemical resistance to acids, alkalies, solvents, and fuels

WearCOAT SG-4 Epoxy Anti-Slip

Two component, rapid curing, self-sealing, heavy duty, nonskid epoxy coating. Designed to provide the highest possible level of anti-slip properties Superior toughness and corrosion resistance Excellent chemical resistance

WearCOAT SG-LP WB Epoxy Anti-Slip

Two component, low VOC, waterborne epoxy with moderate grit. Designed for use in wet areas with heavy pedestrian grade traffic Ideal for use around pools, in locker rooms, showers, boats, docks, walkways, and decks