Aged Surface

Siloxseal 385 Mid Temp Silicone

Silicone modified epoxy coating with enhanced thermal resistance capabilities. Excellent for protecting outdoor structural steel, pipes, and equipment from corrosion. Withstands operating temperatures of up to 400°F (204°C). Adheres well to difficult surfaces such as brass or copper.

U-104 Aluminum-Filled MCU

A single-component, aluminum-filled, moisture-cured urethane, U-104 excels at protecting steel and other substrates from corrosion, even over pre-rusted surfaces. Because it bonds and encapsulates the substrate, it may not require aggregate blasting for surface preparation. It cures fast, easily allowing two coats in one day. With two or three coats, it can be used as …

U-104 Aluminum-Filled MCU Read More »

U-109 Zinc Rich MCU

U-109 is a two-component, zinc-rich urethane primer for use on metal substrates in severe corrosive or salt environments or anywhere the substrate requires cathodic-type protection from its primer. Designed for easy application by brush, roller or spray, it provides long-term corrosion protection. When paired with U-166, U-499 or U-111 as a topcoat, it provides added …

U-109 Zinc Rich MCU Read More »

U-497 Zinc Rich Epoxy Primer

U-497 is a three-component, zinc-rich polyamide epoxy primer for use on metal substrates in severe corrosive or salt environments or anywhere the substrate requires cathodic-type protection from its primer. Designed for easy application by brush, roller or spray, it provides long-term corrosion protection. When paired with U-166, U-499 or U-111 as a topcoat, it provides …

U-497 Zinc Rich Epoxy Primer Read More »

U-499 Polyamide Epoxy Primer

Designed to be applied in many environments, even on damp surfaces, U-499 is a two-component polyamide epoxy with corrosion inhibiting pigments that helps prevent corrosion and attack from sea-water and chemicals. It will cure when cold, and when cured at normal temperatures, can be ready for immersion in as little as 8 hours.

WearCOAT 1020 WB Epoxy Primer

Two component, water-based penetrating epoxy sealer/primer for protecting concrete surfaces. Quick cure provides a short time to overcoat Low viscosity allows penetration into the pores of concrete for increased adhesion Can be used as a primer, or as a final coat sealer

WearCOAT 1080 Moisture Mitigating Primer

Two component, 100% solids, moisture vapor tolerant epoxy primer for use on mechanically prepared concrete floors. Excellent in lowering moisture vapor pressure prior to applying standard coatings Effective for lowering moisture vapor transmission under resilient flooring and tile

WearCOAT 3045 Darkening Sealer

Excellent water-based sealer yields a wet-look previously only achieved with solvent-based acrylic sealers.  Low-odor, UV-resistant formula cures in as little as 4 hours.  Helps keep water, salts and stains from penetrating while giving a dark, wet appearance.  For indoor or outdoor use on concrete, rock or natural slate-type surfaces.

WearCOAT 440 100% Solids Epoxy

Two component, 100% solids epoxy floor coating. Formulated for general industrial flooring as an excellent high-build mid-coat Can be pigmented or used clear Ideal for use as a broadcast binder for flake, sand, or quartz media Very high resistance to amine blush making it ideal for application in most environments Also available in a fast …

WearCOAT 440 100% Solids Epoxy Read More »

WearCOAT 490 Polyamide Epoxy Primer

Two component polyamide cured epoxy primer. Very surface tolerant and can be applied in damp environments Long recoat window allows excellent topcoat adhesion Usually top coated with WearCOAT 440, WearCOAT 491, or WearCOAT 100